PARKING BRAKE LINING.

TM 55-1740-200-14

strainer (50). Secure strainer with cotter pin (51). Assem-

b. Attach bracket (50) to transmission with four

ble three gaskets (47, 48 and 49) and oil pan (45) to

screws (51), and four washers (52). Secure bellcrank (18)

engine block with 20 screws and washers (46). Install

to bracket (50) with cotter pin (19) and washer (20).

gasket (44) and plug (43) in pan (45).

c. Install differential lockout lever (3) and spring (6)

b. Secure rotor (39) to shaft (41) with pin (40). Insert

on bracket (47) and secure with cotter pin (4) and washer

shaft (41) into housing (42). Secure gear (37) to shaft

(5). Install lubrication fitting (2) and rubber grip (1) on

lever (3).

(41) with pin (38). Install gasket (36) and attach plate

(34) to housing (42) with five screws and washers (35).

Install gasket (33) and insert oil pump assembly in engine

d. Assemble two nuts (16) and two clevis (14 and 15)

block. Secure pump with two screws (31) and washers

to rod (17). Attach link assembly with two cotter pins

(32). Assemble plunger (30), spring (29), gasket (28) and

(12) and pins (13). Assemble two nuts (10), and two

clevis (9) to rod (11). Attach link assembly with two

plug (27) in engine block. Install tube (26) and oil level

indicator (25).

cotter pins (7) and pins (8).

4-569. PARKING BRAKE LINING.

c. Attach bracket (7) with two screws (5) and washers

(6). Secure clamp (12) to bracket (7) with two screws

(8), washers (9), washers (10), and nuts (11). Assemble

4-570. REASSEMBLY. None required.

plug (23), cup and spring (22), and filter (20) in housing

(24). Install gaskets (21) and secure cover (17) to housing

4-571. INSTALLATION. See figure 4-35 and install

(24) with screw (18) and washer (19).

the parking brake components as follows:

d. Insert engine oil filter in clamp (12) and secure

a. Secure bracket (14) to transmission (32) with

with screw (13), two washers (14 and 15), and nut (16).

screws (15) and washers (16). Secure bracket (22) with

Install elbow (4), three elbows (3), and two tubes (1 and

screws (23) and washers (24). Attach lining (18) to brake

2).

band (20) with 28 rivets (19). Secure brake band assem-

bly and spring (21) with screw (17 and 12) and two nuts

e. Attach housing (24) and bracket assembly (7) to

(13).

engine with four screws (8), washers (9), washers (10) and

b. Assemble two springs (11), cam shoe (10) special

nuts (11). Install two adapters (14, figure 4-37), elbows

(15) and nut (16). Install two hoses (18) and tube

bolt (9), spring (8), and washer (7) on brake band (20)

assembly (19).

and secure with two nuts (5) and washer (6). Assemble

two levers (4) and links (3) on bolt (9) with two pins (2)

f. Install filter (28). Install cover screw assembly (25),

and cotter pins (l).

washer (26), cover (27), gasket (29), gasket (30). Ensure

c. Install yoke (27) on brake drum (31) with four

gasket (29) seats properly. Install drain plug (23).

screws (28), washers (29) and nuts (30). Secure yoke and

drum assembly to transmission shaft with nut (26) and

4-575. ENGINE AND TRANSMISSION ASSEMBLY.

cotter pin (25). Install the rear axle propeller shaft as

outlined in paragraph 4592.

4-576. REASSEMBLY. None required.

d. Install the transmission propeller shaft as outlined

in paragraph 4589.

4-577. INSTALLATION. See figure 437 and install

the engine, hydraulic transmission, transmission and trans-

4-572. OILING GROUP.

fer case as follows:

4-573. REASSEMBLY. None required.

a. Attach two support brackets (11) to hydraulic

transmission (41) with eight screws (12) and washers (13).

4-574. INSTALLATION. See figure 4-36 and install

Install transfer transmission (57) and secure four screws

the engine oiling components as follows:

(7), washer (8 and 9), and nuts (10).

a. Install two adapters (56), nuts (54), and tube (55)

b. Install propeller shaft (figure 4-39) and mechanical

in engine block. Attach seal plate (57) with two screws

transmission (50).

(58) and washers (59). Install pipe (53), adapter (52), and

4-121