GOVERNOR.

TM 55-1740-200-14

c. Install top hose (4) and secure with two clamps (3).

4-554. GOVERNOR.

Fill radiator with coolant and install radiator cap (18).

4-555. REASSEMBLY. See figure 4-31 and reassemble

4-563. ENGINE COOLING GROUP.

the governor as follows:

4-564. REASSEMBLY. None required.

a. Install disk (25), two covers (24), two bearings (13

and 23), and plug (22) in body (26).

4-565. INSTALLATION. See figure 433 and install

the engine cooling components as follows:

b. Assemble piston (20) and clip (19) on rod (21).

Insert rod and plug (18) in body (26). Install bushing

a. Insert shaft (27) in pump housing (28) and secure

(15) on screw (16). Insert spring assembly (17), screw

(16), and cap (14) in body (26).

with clip (21). Assemble seal assembly (25), washer (24),

and retaining ring (23) in impeller (22). Install thrower

(26) and impeller (22) on shaft (27). Attach gasket (20)

c. Secure cam (11) on shaft (12) with pin (1O). Insert

and plate (17) to housing (28) with three screws (18),

shaft assembly and secure with two clips (8 and 9).

and one washer (19).

Attach valve (5) to shaft (12) with two screws (6) and

washers (7). Install gasket (4) and secure cover (1) with

two screws (2 and 3).

b. Install gasket (16) and pump assembly to engine

block with four screws (15). Install thermostat (14), two

4-556. INSTALLATION. See figure 4-28.

gaskets (12 and 13) and housing (10). Secure housing to

engine head with two screws (11). Install hose (8) and

a. Install two studs (22 and 23) in adapter (29).

two clamps (9).

Attach adapter and gasket (32) to intake manifold with

two screws (30 and 31).

c. Secure hub (6) to shaft with pin (7). Attach pulley

(5) and fan (1) to pump assembly with four screws (2)

b. Assemble gasket (28), governor (27), gasket (26).

and washers (3). Install belt (4).

4-557. FUEL TANK.

4-566. PARKING BRAKE AND DIFFERENTIAL

4-558. INSTALLATION. See figure 4-28 and install as

LOCKOUT LEVERS.

follows:

4-567. REASSEMBLY. See figure 4-34 and reassemble

a. Install fuel tank (7) and secure with two straps (4)

the parking brake lever as follows:

and four nuts (5).

a. Assemble bushing (45), spacer (43), link (42) and

b. Install plug (3) and filler cap (6) in tank (7).

pin (41) to bellcrank (38). Install two spacers (44) and

bellcrank (38) on bracket (46) and secure with pin (39)

4-559. COOLING SYSTEM.

and retaining ring (40).

4 - 5 6 0 . RADIATOR.

b. Install adjusting screw (33) in tube (34) and insert

tube in bracket assembly (46). Secure tube (34) with pin

4-561. REASSEMBLY. None required.

(35), two washers (36), and retaining ring (37). Install

base (32), washer (31) and cap (30).

4-562. INSTALLATION. See figure 4-32 and install

the cooling system components as follows:

4-568. INSTALLATION. Install the parking brake and

a. Install radiator (19) and secure with two screws

differential lockout levers as follows:

(14), four washers (15 and 16), and two nuts (17). Install

four screws (9), washers (11), and nuts (13). Install drain

a. Attach bracket (47) to transmission with two screws

cock (8) in radiator (19).

(48) and washers (49). Secure parking brake lever to

bracket (47) with two screws (27) washers (28), and nuts

b. Install two hoses (6) and connector (7) and secure

(29). Assemble nut (25) and two clevis (23 and 24) to

with four clamps (5). Assemble elbow (2) and adapter (1)

rod (26). Install link assembly and secure with two pins

to connector (7).

(22) and cotter pins (21).

4-120