INSTALLATION - TM-55-1740-200-140163

TM 55-1740-200-14

4-469. INSTALLATION. See figure 4-3 and install the

4-472. INSTALLATION. See figure 4-4 and install the

upper cab assembly as follows:

lower half cab as follows:

a. Lift upper half cab onto the tractor. Secure cab

a. Attach cab assembly to frame with four screws

with 24 screws (1), 48 washers (2), 24 washers (3), and

(67), washers (68), and nuts (69).

24 nuts (4).

b. Install two springs (71), washers (72), nuts (73) and

b. Install right and left door assemblies with six hinge

screws (70).

springs (11), twelve screws (8), washers (9), and nuts

(10).

4-473. ENGINE COMPARTMENT HOOD.

4-470. LOWER CAB ASSEMBLY.

4-474. REASSEMBLY. See figure 4-5 and reassemble

the engine compartment hood as follows:

4-471. REASSEMBLY. See figure 4-4 and reassemble

the lower half cab as follows:

a. Assemble two curved panels (15 and 16) to center

panel (17) with two rods (12). Assemble two louvered

panels (13 and 14) to panels (15 and 16) with two rods

a. Install left floor plate (65) with twelve screws (60).

(12).

Install right floor plate (63) with ten screws (64).

b. Attach two handles (10) to two panels (13 and 14)

b. Secure right floor panel (61) with six screws (62).

with four rivets (11). Secure four catches (8) with eight

Secure center floor panel (59) with six screws (60).

rivets (9).

Secure left floor panel (57) with five screws (58). Secure

left floor panel (56) with four screws (54). Install bushing

c. Secure four fasteners (4) to two panels (6 and 7)

(55)

with eight rivets (5).

c. Attach hydraulic transmission access cover (52) to

4-475. INSTALLATION. Install the engine compart-

toe board (59) with two screws (53). Attach identifi-

ment hood as follows:

cation plate (36) with four screws (37). Attach instruc-

tion plate (34) with four screws (35).

a. Install hood assembly on tractor and secure with

two screws, washers and nuts.

d. Install two door strikers (74) with four screws (75).

Install four grommets (49 and 50).

b. Install two side panels (6 and 7) with eight screws

(l), washers (2), and nuts (3).

e. Assemble four brackets (43 and 44) to two tubes

(48) and secure with eight screws (45), washers (46) and

4-476. DOOR ASSEMBLY.

nut (47).

4-477. REASSEMBLY. See figure 4-6 and reassemble

f. Secure two handles (38) to cab with eight screws

the vehicle door as follows:

(39), washers (40 and 41) and nuts (42). Install firewall

brace (30) with screw (31), washer (32), and nut (33).

a. Install three hinges and shims (25 and 30) on the

exterior panel (31) with two screws (27), four screws

g. Secure two seat bases (26) with eight screws (27),

(26), six washers (28) and six nuts (29). Install weather

washers (28), and nuts (29). Install two seat adjusters (22

strips (23 and 24).

and 23) and driver seat (18) with eight nuts (24) and

washers (25). Install passenger seat (18) with four screws

b. Install regulator (19) on panel (13) with six screws

(19), washers (20) and nuts (21).

(20), washers (21) and nuts (22). Insert channel (18) and

glass (17). Secure interior panel assembly with nine screws

h. Secure retainer (14) with twelve screws (15),

(14), washers (15) and washers (16).

washers (16), and nuts (17). Secure weatherstrip (13) to

door (9). Install lid with three screws (10), washers (11),

c. Assemble plate (10), shaft (9) and secure with

and nuts (12).

retaining ring (8). Install handle assembly, shims (11) and

latch (12) with four screws (6) and nuts (7). Attach plate

i. Assemble spring (8) and plunger (5) and secure with

rivet (6) and nut (7). Secure handle (1) to door (9) with

(5), spring (4) and handle (1) to panel assembly and

secure with screw (2) and washer (3).

two screws (2), washers (3), and nuts (4).

4-111