TIE ROD ENDS.

TM 55-1740-200-14

g. Install contact (5), spring (4) and cup (3). Place

NOTE

horn button (2) on wheel (13). Push button and turn

Replace corroded washers and reinstall as

one-third turn to secure. Install cover (1).

shown in figure 416 to comply with

MIL-S-10379 radio suppression requirements

4-505. INSTALLATION. Install the steering gear as

for non-tactical vehicles.

follows:

a. Install adapter (101) and oil pressure tube assembly

a. See figure 4-8 and install steering gear (110).

(100).

Secure with two screws (111 and 112) and washers (113).

b. Install battery (115) as outlined in Chapter 3,

b. See figure 4-15 and secure steering arm (26) with

Section VI. Install cab heater (99) as outlined in para-

nut (22) and washer (23).

graph 4-544.

c. Connect the front drag link valve as outlined in

c. Secure bracket (95) to cab with two screws (96),

paragraph 4-487.

washers (97) and nuts (98). Attach headlight (94) to

bracket (95) with one nut and washer.

4-506. TIE ROD ENDS.

d. Install spotlight (90) as outlined in paragraph 6-91

4-507. REASSEMBLY. See figure 4-8 and reassemble

with screws (91), washers (92) and nuts (93).

the tie rod ends as follows:

e. Secure bracket (86) with two screws (87), washers

a. Assemble two bolts (43), washers (44), nuts (45)

(88) and nuts (89). Attach floodlight (82) to bracket (86)

and one pipe plug (42) in body (58).

with two screws (83), washers (84), and nuts (85).

b. Assemble bearing (57), ball stud (56), packing (55),

f. Secure bracket (78) with two screws (79), washers

spring seat (54), spring (53), plug (52) and retaining ring

(80) and nuts (81). Attach taillight (77) to bracket (78)

(51) in body (58).

with two nuts (81) and washers (80).

c. Install washer (50), packing (49), dust shield (48),

and spring (47) in body (58).

g. Install bracket and motor assembly (73) and secure

with four screws (74), eight washers (75), and four nuts

4-508. INSTALLATION. See figure 4-8 and install the

(76). Install wiper blade (68) on arm (69) and attach arm

to wiper motor (73) with one nut and washer.

tie rod ends as follows:

h. Install gasket (67) and transmitter (64) and secure

a. Screw tie rod ends on rod (59) and tighten bolts

with five screws (65) and washers (66). Install neutral

(43).

switch (63). Install knob (62) and lock nut (61). Install

brake switch (60). Secure dimmer switch (57) with two

b. Install nuts (46), cotter pins (39) and lubrication

screws (58) and washers (59).

fittings (38).

i. Attach bracket (53) to firewall with screw (54),

washer (55), and nut (56). Secure horn (50) to bracket

4-509. ELECTRICAL SYSTEM.

(53) with nut (51) and washer (52). Secure relay (44)

with two screws (46), washers (47), and nuts (48). Attach

NOTE

solenoid (42) with nut (43).

j. Install regulator (34) and secure with three screws

Spray all terminals and wire repairs to protect

(35), washers (36) and nuts (37).

against fungus in accordance with MIL-V-1 73.

k. Install capacitors (18) and secure retaining straps

4-510. REASSEMBLY. None required.

(20 and 21) with screw (22), washer (23), and nut (24).

Attach coil (15) to engine with two nuts (16) and

washers (17). Secure starter motor (10) on flywheel

4-511. INSTALLATION. See figure 4-16 and install

housing with two nuts (11) and washers (12).

the electrical system wiring and components as follows:

4-115