|
| |
TM 9-2320-360-20-1
Section VI. PREPARATION FOR STORAGE OR SHIPMENT
2-22. PREPARATION FOR STORAGE OR SHIPMENT
a.
Instructions in this section apply to the vehicle to make it available for use upon receipt after shipment. The
storage instructions apply to vehicle being taken out of service for a period up to one year with vehicle exercise. If
vehicles are inactive for more than one year they will use extended storage procedures.
b.
Refer to (AR 750-1) for detailed administrative storage instructions.
c.
Refer to (TB 9-2300-422-20) for security procedures.
d.
Perform Preventive Maintenance Checks and Services (PMCS) listed in table 2-1.
e.
Correct all deficiencies noted during the inspection if facilities are available. If repairs required are beyond the
scope of unit maintenance, refer the deficiencies to direct and general support maintenance.
f.
Instructions pertaining to Basic Issue Items (BII) and Components of End Items (COEI) stowage locations are
covered in appendix B and F of (TM 9-2320-360-10).
g.
Remove rust and corrosion, and scrape any flaked and peeling paint. Dry all surfaces to be painted and coated
with preservatives. Refer to (TM 9-247), Materials Used for Cleaning, Preserving, Abrading, and Cementing Ordnance
Material and Related Materials including Chemicals.
h.
Repaint surface, as required, to prevent against deterioration. Refer to (TM 43-0209) for painting instructions for
Field Use, Color, Marking, and Camouflage Painting of Military Vehicles.
CAUTION
During storage tachograph will wear out paper charts. Teflon chart must be
installed when in storage. Failure to comply may damage tachograph.
i.
Replace tachograph paper chart with teflon chart (para 7-15).
2-23. STORAGE MAINTENANCE PROCEDURES
a.
Before placing a vehicle in storage, perform the following tasks:
(1)
Clean the exterior, interior of cab, engine, and undercarriage. Wash any oil, grease, or mud from tires.
(2)
Conduct a visual inspection of the vehicle. Check lubricant levels and tire pressures (CTIS highway setting).
Correct any discrepancies.
(3)
Completely lubricate the chassis and all ancillary equipment in accordance with (LO 9-2320-360-12).
(4)
Check the coolant level. Test the coolant to ensure that the cooling system is protected against corrosion and
temperatures down to -30F (-34C). Add antifreeze or corrosion inhibitors compatible with ethylene glycol base
antifreeze if cooling system is not adequately protected (TB 750-651).
(5)
Ensure the fuel tank contains at least 20 gallons (75.7 L) of treated fuel. The fuel should be treated with Biobor
J.F. (MIL-S-53021 (or equivalent) as a fungus inhibitor. The addition of 3 teaspoons of Biobor to 20 gallons of fuel will
provide adequate protection against fungus growth. When storing a vehicle in freezing conditions, the addition of 3
ounces (88.7 ml) of isopropyl alcohol (MIL-A-10-428) to 20 gallons of diesel fuel will help prevent fuel line freeze up.
(6)
All fuel that is added to the vehicle during storage must be treated. While in storage, there must always be at
least 20 (75.7 L) gallons of treated fuel in the vehicle's fuel tank.
(7)
Check condition of engine air cleaner. Replace if necessary (para 4-2).
(8)
Coat all exposed unpainted surfaces such as spools, drive shafts, and shift cables with grease.
CAUTION
Do not allow the baking soda solution to enter the batteries or damage to batteries
will result.
(9)
Clean batteries and battery cables with a baking soda solution and rinse with fresh water. Add water to battery
electrolyte if necessary. Check the specific gravity of the batteries regularly. Keep the batteries fully charged and clean
(TM 9-6150-200-14).
Change 2 2-989
|
