Figure 4-41. Transfer transmission (Sheet 2 of 2)

TM 55-1740-200-14

55. Washer

1. Screw

28. Washer

56. Bracket

29. Gasket

2. Nut

57. Bearing

30. Spacer

3. Spring

58. Adapter

31. Bearing

4. Pilot

59. Screw

32. Plate

5. Ball

60. Washer

33. Screw

6. Bolt

61. Gasket

34. Washer

7. Nut

62. Seal

35. Gasket

8. Bar

63. Setscrew

36. Housing

9. Boss

64. Screw

37. Screw

10. Screw

65. Ring

11. Washer

38. Screw

66. Fork

39. Washer

12. Seal

67. Gear

40. Gasket

13. Carrier

68. Crossmember

41. Sleeve

14. Screw

69. Screw

42. Gear

15. Washer

70. Washer

43. Screw

16. Shim set

71. Nut

44. Washer

17. Bearing

72. Cover

45. Bushing

18. Washer

73. Screw

46. Housing

19. Housing

74. Washer

47. Gasket

20. Screw

75. Housing

48. Plate

21. Washer

76. Breather

49. Screw

22. Gasket

77. Pin

50. Washer

23. Nut

78. Plug

51. Gasket

24. Yoke

79. Gasket

52. Bracket

25. Seal

80. Spacer

53. Bracket

26. Cap

54. Screw

27. Screw

Figure 4-41. Transfer transmission (Sheet 2 of 2)

d. Remove spring (34). Remove two split washers

a. Remove cover (1). Remove eight screws (28, figure

(30), four flat washers (32) and two spring washers (31).

4-46) and bushings (29) and remove axle shaft (27).

Remove two split washers (33) and remove two shoe

Remove two plugs (2, figure 4-47) and pins (3) and

assemblies.

remove yoke and ring assembly. Remove two spring pins

(4) and pins (5) and remove yoke (6) from ring (9).

e. Remove four screws (25), washers (27) and nuts

Remove two bushings (7) and two bushings (8) from ring

(28). Remove four screws (24), washers (26) and nuts

(9).

(29) and remove shield (23). Remove two screws (50) and

washers (51) and remove the plate assembly. Remove two

b. Remove eight screws (11), two lock plates (10) and

nuts (39) and washers (40) and remove two pins (38).

two shims (14) and remove plate (12) and hub (22).

Remove two bolts (58), cams (56) and springs (57).

Remove two bearings (15), cups (16) and spacer (17).

Remove four pins (53) and collars (54) and remove

Remove twelve screws (19) and remove drum (18) from

bracket (52). Remove four pins (55) and clinch nuts (59)

hub (22). Remove two pins (20) and six studs (21) from

from plate (60).

hub (22).

f. Remove two screws (61), two screws (62), four

washers (63) and four nuts (64) and remove arm (66).

c. Remove two screws (42) and washers (43) and

Remove bushing (65) from arm (66). Remove wedge (77),

remove the cylinder assembly. Remove two rods (41),

cap (78), two bearings (79) and cup (80) and remove

boots (44), pistons (45), cups (46) and springs (47) from

spindle (76) from stud (82).

cylinder (49). Remove valve (48) from cylinder (49).

4-89