TRANSMISSION PROPELLER SHAFT.

TM 55-1740-200-14

a. Provide proper support for transmission and aline

b. Install spacer (80). Attach cross member (68) with

front plate with hydraulic transmission. Secure gasket and

four nuts (71), washers (70) and screws (69). Assemble

seal (62) gasket (61), and adapter (58) with four screws

the mechanical transmission with four screws (55) and

(59) and washers (60).

washers (56).

c. Install gasket (79) and cover (72) on housing (75)

b. Install lever (54), spring (53) and spring seat (52)

and secure with screws (73) and washers (74).

and secure with cover (51).

d. Attach gasket (22) and housing (19) to housing

Install transmission propeller shaft as outlined in

(75) with seven screws (20) and washers (21). Install

paragraph 4-589.

bearing (17), washer (18), and seal (12) in carrier (13).

Attach shim (16) and carrier (13) with four screws (14)

4-587. TRANSMISSION PROPELLER SHAFT.

and washers (15).

4-588. REASSEMBLY. None required,

e. Secure three brackets (52, 53, and 56) with six

screws (54) and washers (55). Attach gasket (51) and

4-589. INSTALLATION. See figure 4-39 and install

plate (48) to cover (72) with four screws (49) and

the transmission propeller shaft as follows:

washers (50).

a. Attach yoke (1) to parking brake drum with four

f. Install bushing (45) in housing (46). Attach gasket

nuts, washers, and spacers. Insert dust cap (14) in yoke

(47) and housing (46) with four screws (43) and washers

(15) and slide yoke on transmission shaft.

(44). Install speedometer gear (42) and sleeve (41) in

housing (46).

b. Insert bearings (11) on cross (12) and secure to

yokes (1 and 2) with eight bolts (3 and 4), four lock

g. Attach boss (9) with three screws (10) and washers

plates (5), and bearing straps (6).

(11). Assemble nut (7) and eyebolt (6) in bar (8) and

insert bar in housing (75). Install ball (5), pilot (4), spring

c. Insert bearings (9) on cross (10). Attach universal

(3), nut (2), and screw (1) in boss (9).

joints assemblies to universal coupling (13) with four

bolts (8),

h. Install gear (67), fork (66) and retaining ring (65).

Lock bar (8) to fork (66) with setscrew (63) and screw

(64). Secure housing (36) and gasket (40) with eight

4-590. AXLE PROPELLER SHAFT.

screws (37 and 38) and washers (39).

4-591. REASSEMBLY. None required.

i. Install bearing (31) and washer (30) in housing (36).

Attach cap (26) and gasket (29) with four screws (27)

4-592. INSTALLATION. See figure 4-40 and reinstall

and washers (28). Install seal (25) and secure yoke (24)

the front and rear axle propeller shaft as follows:

with nut (23). Attach gasket (35) and washer (34) to

housing (36) with two screws (33) and washers (34).

a. Install felt (9), ret airier packing (8), and lubrication

fitting (10) on yoke (11). Assemble four packing retainers

4-595. INSTALLATION. Install the transfer trans-

(6) and four packings (5). Assemble shaft (12), yoke (11),

mission as follows:

two spiders (7) and eight bearings (4).

a. Install transfer transmission on mounting brackets

b. Install propeller shaft and secure eight straps (1)

and secure mounting bolts.

with sixteen screws (2) and washers (3).

b. Install the axle propeller shafts as outlined in

paragraph 4-592.

4-593. TRANSFER TRANSMISSION.

4-596. BRAKE SYSTEM.

4-594. REASSEMBLY. See figure 4-41 and reassemble

the transfer transmission as follows:

4-597. REASSEMBLY. None required.

a. Install plug (78), pin (77), and breather (76) in

4-598. INSTALLATION. See figure 4-42 and install

housing (75).

the brake system tubing and components as follows:

4-123