VOLTAGE REGULATOR - TM-55-1740-200-140101

TM 55-1740-200-14

4-254. VOLTAGE REGULATOR.

b. Remove one nut (9) and washer (10). Remove

screw (12), lock washer (13), two screws (14) and

4-255. REMOVAL. See figure 4-16. Disconnect wires

washers (15) and remove solenoid (11). Remove grommet

from terminals and remove three screws (35), washers

(16) from solenoid (11). Remove core (18), spring (17)

(36), nuts (37), and remove regulator (34).

and boot (19).

c. Remove pinion housing (23). Remove pin (21), fork

4-256. GENERATOR.

(22) and bushing (20) from housing (23).

4-257. REMOVAL. See figure 4-16 and remove the

d. Remove step washer (24), retaining ring (25),

generator as follows:

assembled pinion and clutch, and bushing (31) from

armature (32). Remove retaining ring (27), washer (28)

a. Disconnect wires from terminals.

and spring (29) from pinion (30).

b. Remove two screws (2), washers (3) and nuts (4)

e. Remove screw (34) and brush set (33). Remove

and remove generator (1).

four screws (36), four pole shoes (35) and four coils (37)

from frame (38).

4-258. DISASSEMBLY. See figure 4-18 and disassemble

the generator as follows:

4-262. WINDSHIELD WIPER (Code Cl).

a. Remove nut (2) and washer (3). Remove pulley (1)

and key (4). Remove two bolts (5) and washers (6) and

4-263. REMOVAL. See figure 416. Remove one nut

remove front and rear end bell assemblies.

and washer and remove wiper blade (68) and wiper arm

(69). Remove four screws (74), eight washers (75), and

b. Remove two screws (20) washers (21), and remove

four nuts (76) and remove wiper motor (73).

two brushes (19), two arms (22) and two springs (23).

Remove oiler (24), wick (25) and wick spring (26) from

4-264. DISASSEMBLY. See figure 4-20 and dis-

end bell. Remove bearing (27) from end bell (28).

assemble the windshield wiper as follows:

c. Remove three screws (7) and washers (8), two

a. Remove three screws (1) and washers (2). Remove

washers (9), retainer (10), gasket (11), bearing (12) and

nut (23) and washer (24) and remove motor assembly

retainer (13) from end bell (15). Remove oilcup (14)

from bracket assembly.

from end bell (15).

b. Remove two screws (3) and washers (4). Remove

d. Remove armature (18) and remove retainer (16)

cap assembly from motor. Remove brush (5) and two

and retaining ring (17) from armature shaft. Remove

springs (6) from cap (7).

screw (29) and washer (30) from frame (46).

c. Remove two screws (14) and washers (15). Loosen

e. Remove four nuts (32 and 35), four washers (33

screw (16) and remove motor lug. Remove capacitor (13)

and 36), two washers (34 and 37) and washers (38).

and gasket (18). Remove brush (11) and housing (12).

Remove two screws (40) and remove two pole shoes (43)

and coils (44 and 45).

d. Remove four screws (20) and remove cover (19),

gasket (21) and radio suppression plate (22). Remove gear

4-259. STARTER.

(25) and washer (26) from housing (27).

4-260. REMOVAL. See figure 4-16 and remove two

e. Remove nut (34), washer (35), driver (36), boot

nuts (11) and washers (12). Remove starter (10).

(37), nut (38), washer (39) and felt washer (40) from

shaft (44). Remove two screws (32) and washers (33) and

4-261. DISASSEMBLY. See figure 4-19 and dis-

remove assembled parts from bracket (45).

assemble the starter as follows:

a. Remove two bolts (2) and washers (3). Remove end

f. Remove two spring clips (28) and washers (29).

bell (1) and remove bushing (5) and felt pad (4) from end

Remove connecting link (31) from arm (30) and pin (41).

bell (1). Remove two thrust washers (6) and brush holder

Remove nut (42) and washer (43). Remove pin (41) from

(8). Remove brushes and four springs (7) from holder (8).

shaft (44).

4-49