|
| |
SECTION I
TM 5-241 0-236-24P
(5)
Part
numbers
for
bulk
materials
are
referenced in this column in the line item entry for the
item to be manufactured/fabricated.
(6) When the item is not used with all serial
numbers of the same model, the effective serial numbers
are shown on the last line(s) of the description (before
UOC). Not applicable.
(7) The usable on code, when applicable (see
paragraph 5, Special information).
(8) In the Special Tools List section, the basis of
issue (BOI) appears as the last line(s) in the entry for
each special tool, special TMDE and other special
support
equipment.
When
density
of
equipments
supported exceeds density spread indicated in the basis
of
issue,
the
total
authorization
is
increased
proportionately.
(9) The statement "END OF FIGURE" appears
just below the last item description in Column 5 for a
given figure in both Section II and Section III.
f. QTY (Column (6)). The QTY (quantity per figure
column) indicates the quantity of the item used in the
breakout shown on the illustration figure, which is
prepared for a functional group, subfunctional group or
an assembly. A "V" appearing in this column in lieu of a
quantity indicates that the quantity is variable and the
quantity may vary from application to application.
4. Explanation of Columns (Section IV).
a. NATIONAL STOCK NUMBER (NSN) INDEX.
(1 )STOCK NUMBER column. This column lists
the NSN by National item identification number (NIIN)
sequence. The NIIN consists of the last nine
NSN
digits of the NSN (i.e., 530501674-1467)
NIIN
When using this column to locate an item, ignore the first
4 digits of the NSN. However, the complete NSN should
be used when ordering items by stock number.
(2) FIG. column. This column lists the number of
the Figure where the item is identified/located. The
figures are in numerical order in Section 11 and Section
Ill.
(3) ITEM column. The item number identifies the
item associated with the figure listed in the adjacent FIG.
column. This item is also identified by the NSN listed on
the same line.
b. PART NUMBER INDEX. Part numbers in this
index are listed by part number in ascending 4
alphanumeric sequence (i.e., vertical arrangement of
letter and number combination which places the first
letter or digit of each group in order A through Z, followed
by the numbers 0 through 9 and each following letter or
digit in like order.)
(1)
CAGEC
column.
The
Commercial
And
Government Entity (CAGE) Code (C) is a 5 digit
alphanumeric code used to identify the manufacturer,
distributor or Government agency, etc., that supplies the
item.
(2) PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards, and
inspection requirements to identify an item or range of
items.
(3) STOCK NUMBER column. This column lists
the
NSN
for
the
associated
part
number
and
manufacturer identified in the PART NUMBER and
CAGEC columns to the left.
(4) FIG. column. This column lists the number of
the figure where the item is identified/located in Section
11 and 111.
(5) ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
c. FIGURE AND ITEM NUMBER INDEX.
(1) FIG. column. This column lists the number of
the figure where the item is identified/located in Section II
and Ill.
(2) ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
(3) STOCK NUMBER column. This column lists
the NSN for the item.
(4) CAGEC column. The Commercial And
Government Entity (CAGE) Code (C) is a 5 digit
alphanumeric code used to identify the manufacturer,
distributor or Government agency, etc., that supplies the
item.
(5) PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards and
inspection requirements to identify an item or range of
items.
4
|
